Module 1 · JEE Physics

Laws of Motion, Friction & Circular Motion

Updated 17 Nov 2026 · 8,992 words · 5 sections
Updated 21 Nov 2026
Newton's three laws, free-body diagrams, friction, and circular motion with banking.
Newton's Laws · Friction · Equilibrium · Banking
🎯 Take Mock Test

Learning Objectives

  • Understand the fundamental concepts of Laws of Motion, Friction & Circular Motion
  • Apply key formulas and techniques to solve problems
  • Practice with exam-level questions to build speed and accuracy

1. Newton's Laws of Motion

1.1 The First Law and Inertia

The first law, often called the law of inertia, states that a body remains at rest or continues to move with a constant velocity unless acted upon by a net external force. Inertia is the intrinsic property of matter that resists any change in its state of motion, and its quantitative measure is the mass of the body expressed in kilograms. When the vector sum of all forces acting on a particle is zero, the acceleration of that particle is zero, which means its velocity vector does not change in magnitude or direction. This principle underlies the concept of an inertial reference frame, a frame of reference in which Newton's first law holds true; any frame accelerating with respect to an inertial frame is non‑inertial and requires the introduction of fictitious forces to preserve the form of the equations of motion.

Historically, Galileo’s experiments with inclined planes demonstrated that a sphere rolling on a frictionless horizontal surface would continue indefinitely, contradicting the Aristotelian view that a continuous force is needed to sustain motion. Newton formalised this observation, and the first law also serves as a definition of force: a force is that which changes the state of motion of a body. In practical problem solving, the first law is invoked whenever a system is in uniform motion or at rest, allowing us to set the net force equal to zero and write equilibrium equations for the unknown forces.

1.2 The Second Law and the Concept of Force

The second law provides the quantitative relationship between force, mass, and acceleration: the net force acting on a particle equals the product of its mass and its acceleration, expressed as F = m a. Here force is measured in newtons (N), mass in kilograms (kg), and acceleration in metres per second squared (m s⁻²). The law is a vector equation, meaning that the direction of the acceleration is the same as the direction of the net force. When several forces act simultaneously, the net force is the vector sum of the individual forces, and the acceleration follows that resultant. This formulation allows us to treat force as the cause of acceleration and to predict the motion of a body when the forces are known, or conversely to deduce the forces when the motion is observed.

An important consequence of the second law is the definition of the unit of force: one newton is the force required to give a one‑kilogram mass an acceleration of one metre per second squared. The law also extends to systems of particles by introducing the centre of mass; the total external force on a system equals the total mass times the acceleration of the centre of mass. In many textbook problems the second law is applied component‑wise along chosen axes, turning the vector equation into a set of scalar equations that can be solved simultaneously for unknown magnitudes and directions.

1.3 The Third Law and Action‑Reaction Pairs

The third law states that for every action there is an equal and opposite reaction: if body A exerts a force on body B, then body B simultaneously exerts a force of equal magnitude and opposite direction on body A. These two forces constitute an action‑reaction pair; they act on different bodies, never on the same body, and therefore they do not cancel each other in the free‑body diagram of a single object. The law reflects the conservation of momentum in an isolated system, because the internal forces between components of the system occur in equal and opposite pairs, leaving the total momentum unchanged.

In practice, the third law is essential for identifying all forces acting on a body. For example, when a block rests on a horizontal table, the block exerts a downward force on the table (its weight transmitted through contact) and the table exerts an upward normal force on the block; these two forces are an action‑reaction pair. Similarly, the tension in a massless string is the same throughout because each segment pulls on its neighbours with equal and opposite forces. Recognising action‑reaction pairs prevents the common mistake of double‑counting forces or omitting a reaction force that is crucial for equilibrium or dynamics analysis.

2. Free‑Body Diagrams and Equilibrium

2.1 Constructing a Free‑Body Diagram

A free‑body diagram (FBD) is a pictorial representation that isolates a single body and shows all external forces acting on it as vectors originating from a dot or a simplified shape representing the body. The first step is to choose the system of interest and to imagine cutting it free from its surroundings, replacing each interaction by a force vector. Contact forces such as normal reaction, friction, and tension are drawn at the points of contact, while field forces like weight are drawn acting at the centre of gravity. Each force is labelled with its symbol (e.g., N for normal, f for friction, T for tension, W for weight) and, when known, its magnitude and direction.

Accurate FBDs are the foundation of every dynamics problem because they translate a physical situation into a set of vector equations. The coordinate axes are usually chosen to simplify the components: one axis along the direction of motion or anticipated acceleration, and the other perpendicular to it. Forces that are not aligned with the axes are resolved into components using trigonometric functions. The diagram must include all forces, even those that later turn out to be zero, because omitting a force leads to an incorrect net force and consequently an erroneous acceleration.

2.2 Translational Equilibrium and the Vector Sum of Forces

Translational equilibrium occurs when the vector sum of all forces acting on a body is zero, resulting in zero acceleration of the centre of mass. In component form this condition reads ΣFₓ = 0 and ΣFᵧ = 0 for a planar problem, or ΣFₓ = 0, ΣFᵧ = 0, ΣF_z = 0 in three dimensions. When a body is at rest or moves with constant velocity, these equations hold and can be used to solve for unknown forces such as the normal reaction on an inclined plane or the tension in a supporting cable. The equilibrium equations are simply the static limit of Newton’s second law, obtained by setting a = 0.

It is important to distinguish between static equilibrium (body at rest) and dynamic equilibrium (body moving with constant velocity). Both satisfy the same force‑balance equations, but the former often involves static friction that can vary up to a maximum value, whereas the latter involves kinetic friction of a fixed magnitude. In many engineering applications, structures are designed to remain in static equilibrium under expected loads, and the equilibrium equations are the starting point for stress analysis.

2.3 Rotational Equilibrium and the Moment of Forces

Rotational equilibrium requires that the sum of all torques (moments of forces) about any point be zero: Στ = 0. Torque is defined as the cross product of the position vector from the chosen pivot to the point of force application and the force vector, τ = r × F, with magnitude τ = r F sinθ where θ is the angle between r and F. The direction of the torque vector follows the right‑hand rule and indicates the sense of rotation the force would produce if it were the only force acting. For a rigid body in complete equilibrium, both translational and rotational equilibrium conditions must be satisfied simultaneously.

When solving problems involving beams, ladders, or seesaws, it is often convenient to take moments about a point where one or more unknown forces act, because their torques about that point are zero and they drop out of the moment equation. This technique reduces the number of unknowns in the torque equation, allowing the remaining unknowns to be found. The principle of moments is also the basis for the design of simple machines such as levers and pulleys, where a small force applied at a large distance can balance a large force applied at a short distance.

Example: Block on an Inclined Plane with Friction
A 5 kg block rests on a rough plane inclined at 30° to the horizontal. The coefficient of static friction between the block and the plane is 0.4. Determine whether the block remains at rest or begins to slide, and if it slides, find its acceleration down the plane (take g = 9.8 m s⁻²).
First draw the free‑body diagram. The weight W = mg = 5 × 9.8 = 49 N acts vertically downward. Resolve W into components parallel (W∥ = W sin30° = 49 × 0.5 = 24.5 N) and perpendicular (W⊥ = W cos30° = 49 × √3/2 ≈ 42.4 N) to the plane. The normal reaction N equals W⊥ because there is no acceleration perpendicular to the plane, so N ≈ 42.4 N. The maximum static friction is fₛₘₐₓ = μₛ N = 0.4 × 42.4 ≈ 16.96 N. Since the component of weight down the plane (24.5 N) exceeds the maximum static friction (16.96 N), the block cannot remain at rest and will slide. Once sliding, kinetic friction acts; assuming μₖ = 0.3 (typical for the same surfaces), the kinetic friction force is fₖ = μₖ N = 0.3 × 42.4 ≈ 12.7 N. The net force down the plane is Fₙₑₜ = W∥ – fₖ = 24.5 – 12.7 = 11.8 N. Using Newton’s second law, a = Fₙₑₜ / m = 11.8 / 5 = 2.36 m s⁻² down the incline.
Exam‑Day Insight
When a problem gives only the coefficient of static friction, always compare the required friction for equilibrium with the maximum static friction before assuming motion; many candidates lose marks by directly applying kinetic friction without checking the static limit.

3. Friction

3.1 Nature of Contact Forces and the Origin of Friction

Friction is a contact force that arises from electromagnetic interactions between the microscopic asperities of two surfaces in contact. When two solid bodies press against each other, the real area of contact is only a tiny fraction of the apparent macroscopic area because surfaces are rough at the microscopic level. The interlocking of these asperities and the adhesive forces between atoms at the contact points resist relative motion. The frictional force acts tangentially to the surfaces and opposes the direction of impending or actual sliding. Its magnitude depends on the nature of the materials, the normal force pressing the surfaces together, and the condition of the surfaces (clean, lubricated, oxidised).

Because friction originates from atomic‑scale forces, it is not a fundamental force like gravity or electromagnetism but a macroscopic manifestation of electromagnetic interactions. The empirical laws of friction, first systematically studied by Leonardo da Vinci and later by Guillaume Amontons and Charles‑Augustin de Coulomb, state that the frictional force is approximately proportional to the normal force and independent of the apparent contact area. These laws hold reasonably well for dry, unlubricated surfaces over a wide range of loads and speeds, but they break down at very high pressures, very low loads, or when surface films and temperature effects become significant.

3.2 Static and Kinetic Friction Coefficients

Static friction acts when there is no relative motion between the surfaces; its magnitude can vary from zero up to a maximum value fₛₘₐₓ = μₛ N, where μₛ is the coefficient of static friction and N is the normal force. The actual static friction force adjusts itself to exactly balance the applied tangential force up to this limit, which is why a block on an incline can remain stationary over a range of angles. Once the applied force exceeds fₛₘₐₓ, the surfaces begin to slide and kinetic (or dynamic) friction takes over. Kinetic friction is usually smaller than the maximum static friction and is given by fₖ = μₖ N, where μₖ is the coefficient of kinetic friction. Both coefficients are dimensionless numbers that depend on the pair of materials in contact; typical values for steel on steel are μₛ ≈ 0.6 and μₖ ≈ 0.4, while for rubber on dry concrete μₛ can be as high as 1.0.

The distinction between static and kinetic friction is crucial in problems involving impending motion, such as a ladder leaning against a wall or a car accelerating without wheel slip. In the former case the friction force is whatever is needed to maintain equilibrium, up to μₛ N; in the latter the friction force is fixed at μₖ N once sliding occurs. Some textbooks also introduce a coefficient of rolling friction for wheels, which is orders of magnitude smaller than sliding friction because the contact patch deforms rather than slides.

3.3 Angle of Repose and Limiting Friction

The angle of repose is the steepest angle of an inclined plane at which a body placed on it remains at rest without any external force other than gravity and friction. At this angle the component of weight parallel to the plane exactly equals the maximum static friction: mg sinθᵣ = μₛ mg cosθᵣ, which simplifies to tanθᵣ = μₛ. Thus the coefficient of static friction can be measured experimentally by gradually increasing the incline until the block just begins to slide and then taking the arctangent of that angle. The concept of limiting friction is the same maximum static friction that appears in the angle‑of‑repose condition; it represents the threshold beyond which motion initiates.

In engineering, the angle of repose is used to design stable slopes for granular materials such as sand, gravel, or coal, where the internal friction between particles plays the same role as the friction between a block and a plane. For cohesive soils the angle of repose is supplemented by cohesion, but the basic frictional component still follows the tanθ = μ relationship. Understanding limiting friction also helps in analysing the self‑locking condition of screws and wedges, where the thread angle must be less than the angle of repose for the device to hold a load without continuous torque.

Comparison of Static and Kinetic Friction
PropertyStatic FrictionKinetic Friction
Symbolfₛfₖ
Maximum magnitudeμₛ Nμₖ N (constant)
Dependence on applied forceVariable, matches applied force up to limitIndependent of applied force once sliding
Typical coefficient values (steel on steel)μₛ ≈ 0.6μₖ ≈ 0.4
DirectionOpposes impending motionOpposes actual motion

4. Circular Motion

4.1 Uniform Circular Motion and Centripetal Acceleration

Uniform circular motion occurs when a particle moves along a circular path with constant speed. Although the speed is constant, the velocity vector continuously changes direction, so the particle experiences an acceleration directed toward the centre of the circle. This centripetal acceleration has magnitude a_c = v² / r = ω² r, where v is the linear speed, ω is the angular speed in radians per second, and r is the radius of the circular path. The acceleration is always perpendicular to the instantaneous velocity, which is why the speed does not change. According to Newton’s second law, a net force of magnitude F_c = m a_c = m v² / r must act toward the centre; this force is called the centripetal force. It is not a new kind of force but the resultant of real forces such as tension, gravity, normal reaction, or friction that have a component pointing toward the centre.

In many textbook problems the centripetal force is provided by a single identifiable force: for a satellite in orbit it is gravity, for a car on a flat curve it is friction, for a mass on a string it is tension. When several forces contribute, their radial components are summed to give the required centripetal force. The direction of the centripetal force is always radially inward, and there is no outward “centrifugal force” in an inertial frame; the sensation of being pushed outward in a turning vehicle is due to the inertia of the body tending to continue in a straight line while the vehicle turns inward.

4.2 Dynamics of Non‑Uniform Circular Motion

When the speed of a particle moving on a circular path changes, the motion is non‑uniform circular motion. The acceleration then has two components: a radial (centripetal) component a_r = v² / r directed toward the centre, and a tangential component a_t = dv/dt directed along the tangent in the direction of increasing speed (or opposite if slowing down). The total acceleration vector is the vector sum of these perpendicular components, and its magnitude is a = √(a_r² + a_t²). The net force likewise splits into a radial component F_r = m a_r providing the centripetal force, and a tangential component F_t = m a_t responsible for changing the speed.

Typical examples include a pendulum swinging in a vertical circle, where gravity supplies both a tangential component (changing speed) and a radial component (part of the centripetal force), and a car accelerating on a curved road, where the engine’s traction provides a tangential force while friction and banking supply the radial force. In such problems it is essential to write separate equations for the radial and tangential directions, because the radial equation still enforces the circular geometry (v² / r) while the tangential equation follows from the net tangential force.

4.3 Centrifugal Effects in Rotating Reference Frames

In a reference frame that rotates with the particle, Newton’s laws do not hold in their simple form unless fictitious forces are introduced. The most important fictitious force is the centrifugal force, which appears to act radially outward with magnitude m ω² r. It balances the real centripetal force in the rotating frame, making the particle appear at rest. Another fictitious force, the Coriolis force, acts on objects moving relative to the rotating frame and is proportional to the cross product of the frame’s angular velocity and the object’s velocity in that frame. These fictitious forces are not due to any physical interaction but are mathematical devices that allow the use of Newton’s second law in non‑inertial frames.

Understanding centrifugal effects is important for analysing devices such as centrifuges, where the outward fictitious force in the rotating frame explains the separation of components by density, and for understanding the apparent weight reduction at the Earth’s equator due to the planet’s rotation. In an inertial frame the same phenomena are explained solely by the requirement for a centripetal force; the fictitious forces simply provide an alternative, often more intuitive, description for observers who are themselves rotating.

Uniform vs Non‑Uniform Circular Motion
AspectUniform Circular MotionNon‑Uniform Circular Motion
SpeedConstantChanges with time
Acceleration componentsOnly radial (centripetal) a_r = v²/rRadial a_r = v²/r and tangential a_t = dv/dt
Net force directionPurely radial inwardRadial inward plus tangential along motion
Typical examplesSatellite in circular orbit, mass on horizontal stringPendulum in vertical circle, car accelerating on curve

5. Banking of Roads and Applications

5.1 Derivation of the Banking Angle for a Frictionless Curve

When a road is banked, the normal reaction from the road surface has a horizontal component that can supply the required centripetal force for a vehicle to negotiate the curve without relying on friction. Consider a vehicle of mass m moving with speed v on a curve of radius r banked at an angle θ to the horizontal. The forces acting on the vehicle are its weight mg vertically downward and the normal reaction N perpendicular to the road surface. Resolving N into vertical and horizontal components gives N cosθ upward and N sinθ toward the centre of the curve. For vertical equilibrium, N cosθ = mg. The horizontal component provides the centripetal force: N sinθ = m v² / r. Dividing the second equation by the first eliminates N and yields tanθ = v² / (r g). This is the ideal banking angle for a given speed and radius when friction is absent; at this angle a vehicle can travel exactly at speed v without any sideways frictional force.

The derivation shows that the banking angle depends only on the design speed and the curve radius, not on the mass of the vehicle. In practice, roads are built for a range of speeds, so the banking angle is chosen as a compromise; vehicles travelling slower than the design speed will tend to slide down the bank, while faster vehicles will tend to slide up, and friction must supply the difference. The formula also assumes the road surface is rigid and the vehicle’s centre of mass is at the same height as the contact patch, which is a reasonable approximation for most passenger cars.

5.2 Role of Friction on a Banked Turn

When friction is present, the total horizontal force toward the centre is the sum of the horizontal component of the normal reaction and the horizontal component of the friction force. The friction force acts parallel to the road surface and can point either up the bank (if the vehicle is slower than the design speed) or down the bank (if the vehicle is faster). Its maximum magnitude is f_max = μ N, where μ is the coefficient of static friction between tyres and road. By writing the vertical and horizontal force balances with friction included, one obtains two limiting speeds: a minimum speed v_min = √[ r g (tanθ – μ) / (1 + μ tanθ) ] and a maximum speed v_max = √[ r g (tanθ + μ) / (1 – μ tanθ) ]. Between these speeds the vehicle can negotiate the curve without skidding, and the required friction is less than the maximum available.

These expressions reduce to the frictionless result when μ = 0, and they show that a steeper banking angle (larger θ) increases both v_min and v_max, widening the safe speed range. However, excessively steep banking can be dangerous for slow‑moving or stationary vehicles, which may slide down the incline. Engineers therefore select a banking angle that provides a comfortable speed range for the expected traffic while keeping the required friction coefficient within the capabilities of typical tyres on wet or dry pavement.

5.3 Design Considerations for High‑Speed Tracks

Racing circuits and high‑speed test tracks often employ variable banking, where the angle changes along the curve to match the increasing speed of the vehicle as it accelerates out of a corner. The design process uses the same force‑balance equations but incorporates the vehicle’s aerodynamic downforce, which adds to the normal force and therefore increases the available friction. Downforce is proportional to the square of the speed and acts vertically downward, effectively increasing the apparent weight of the car. This allows higher cornering speeds without increasing the banking angle, which would be impractical for road cars. Additionally, the track surface is engineered to provide a high and consistent coefficient of friction, and the transition from flat to banked sections is made gradual to avoid sudden changes in lateral acceleration that could unsettle the vehicle.

Safety barriers, runoff areas, and the geometry of the banking are all analysed using the principles of circular motion and friction discussed earlier. The goal is to ensure that even if a vehicle exceeds the design speed, the resulting lateral forces remain within the limits that the tyres, suspension, and driver can tolerate. Modern simulation tools integrate the equations of motion for a full vehicle model, but the underlying physics remains the balance of weight, normal reaction, friction, and centripetal requirement that we have derived from Newton’s laws.

The study of forces, friction, and circular motion provides the foundation for analysing a vast range of mechanical systems from simple blocks on inclines to sophisticated transportation infrastructure.

Pseudo Forces in Non‑Inertial Reference Frames

Newton’s laws are formulated for inertial frames — frames that move with constant velocity. When an observer uses a frame that accelerates or rotates, the equation F = ma no longer holds unless additional forces, called pseudo forces or inertial forces, are introduced. A pseudo force has magnitude m aframe and acts opposite to the acceleration of the non‑inertial frame. In a linearly accelerating frame (for example a car speeding up), every mass experiences a backward pseudo force m a. In a uniformly rotating frame with angular velocity ω, two pseudo forces appear: the centrifugal force m ω² r directed radially outward, and the Coriolis force 2 m (ω × vrel) acting perpendicular to the relative velocity vrel of the particle in the rotating frame. These forces are not the result of any physical interaction; they are mathematical devices that allow Newton’s second law to be applied in the accelerating frame.

The centrifugal force is responsible for the apparent outward push felt by a passenger in a turning vehicle. If the vehicle follows a circular path of radius r at speed v, the required centripetal acceleration is v² / r. In the vehicle’s frame the passenger is at rest, so the net radial force must be zero. The real forces are the normal reaction from the seat and the friction from the seat belt; the pseudo centrifugal force balances their inward components. The Coriolis force becomes important when an object moves radially on a rotating platform. For a particle sliding outward on a frictionless turntable, the Coriolis force deflects its trajectory sideways, producing a curved path in the rotating frame even though the inertial trajectory is a straight line.

When solving problems in non‑inertial frames, the standard procedure is: (1) identify the acceleration of the frame, (2) draw a free‑body diagram including all real forces, (3) add the appropriate pseudo forces, (4) write Newton’s second law in the non‑inertial frame. This method is especially powerful for systems where the frame’s motion is prescribed, such as a block on an accelerating wedge, a pendulum in an accelerating lift, or a bead on a rotating hoop. Care must be taken to distinguish between the frame’s angular velocity and the particle’s angular velocity relative to the frame; the Coriolis term involves the relative velocity only.

A common pitfall is to treat the centrifugal force as a real interaction force and to include it in action‑reaction pairs. It has no reaction counterpart because it arises solely from the choice of frame. Another error is to omit the Coriolis force when the particle has a velocity component perpendicular to the rotation axis. In many textbook problems the Coriolis term vanishes because the motion is purely radial or purely tangential, but in general it must be retained. Mastery of pseudo forces enables the analysis of weather systems (Coriolis effect on wind), the design of rotating machinery, and the interpretation of experiments performed in accelerating laboratories.

Rolling Motion and the Condition for Pure Rolling

Rolling without slipping is a constrained motion where the instantaneous point of contact between a body and a surface has zero velocity relative to the surface. For a cylinder or sphere of radius R rolling on a horizontal plane, the translational velocity of the centre of mass v and the angular velocity ω satisfy v = ω R. Differentiating gives the acceleration relation a = α R, where α is the angular acceleration. The static friction force at the contact point provides the necessary torque for angular acceleration but does no work because the contact point is instantaneously at rest. Consequently, mechanical energy is conserved in pure rolling on a fixed rough surface if no other dissipative forces act.

Consider a uniform solid cylinder of mass m and radius R released from rest on an inclined plane of angle θ. The forces are weight mg, normal reaction N = mg cosθ, and static friction f acting up the plane. The translational equation is mg sinθ − f = m a. The rotational equation about the centre is f R = I α, with moment of inertia I = ½ m R² for a solid cylinder. Using a = α R gives f = ½ m a. Substituting into the translational equation yields a = (2/3) g sinθ and f = (1/3) mg sinθ. The friction required is less than the maximum static friction μs N provided μs ≥ (1/3) tanθ. If the coefficient is smaller, slipping occurs and kinetic friction takes over, reducing the acceleration to a = g (sinθ − μk cosθ).

The direction of static friction in rolling is often misunderstood. On an incline, friction acts up the plane for a cylinder rolling down, because the weight component tends to spin the cylinder faster than translation would allow. Conversely, if a torque is applied to the cylinder (e.g., by a string wound around it) causing it to roll up the incline, friction acts down the plane. In all cases, static friction adjusts to enforce the no‑slip constraint v = ω R. The work‑energy theorem for rolling includes both translational and rotational kinetic energy: K = ½ m v² + ½ I ω². For a body rolling down a height h, energy conservation gives mgh = ½ m v² + ½ I (v² / R²), leading to v = √[ 2gh / (1 + I / (m R²)) ]. This shows that objects with larger moment of inertia (e.g., a hollow sphere) reach the bottom later than those with smaller moment of inertia (e.g., a solid sphere).

Rolling with slipping introduces kinetic friction, which does negative work and converts mechanical energy into heat. The equations of motion then become mg sinθ − μk mg cosθ = m a and μk mg cosθ R = I α, with no kinematic link between a and α. The transition from slipping to pure rolling occurs when the condition v = ω R is finally satisfied; after that instant static friction may take over if the required friction does not exceed μs N. Problems involving a ball projected onto a rough horizontal surface with initial spin but no translation, or a cylinder pulled by a horizontal force applied at its centre, are classic illustrations of this transition.

Free‑body diagram with pseudo force
A block of mass m rests on a horizontal turntable rotating with constant angular speed ω. The coefficient of static friction between the block and the turntable is μ. Determine the maximum distance rmax from the centre at which the block can remain at rest relative to the turntable.
In the rotating frame the block is at rest, so the net force is zero. Real forces: weight mg downward, normal reaction N = mg upward, static friction f directed radially inward (opposing the tendency to slide outward). Pseudo force: centrifugal force m ω² r directed radially outward. Radial equilibrium: f = m ω² r. The maximum static friction is fmax = μ N = μ mg. Setting m ω² rmax = μ mg gives rmax = μ g / ω². If the block is placed beyond this radius, the required inward friction exceeds the limit and the block slips outward.
Exam‑day strategy
When a problem mentions a rotating or accelerating platform, immediately decide whether to work in the inertial frame (using centripetal acceleration) or the non‑inertial frame (adding pseudo forces). In the non‑inertial frame, draw the pseudo forces first; they are always opposite to the frame’s acceleration. This reduces sign errors and makes the equilibrium equations straightforward.

Vertical Circular Motion and Critical Speeds

Vertical circular motion differs from horizontal circular motion because the weight of the particle has a component along the radial direction that varies with the angular position. Consider a particle of mass m attached to a light inextensible string of length L moving in a vertical circle. At an angle θ measured from the lowest point, the radial forces are tension T toward the centre and the radial component of weight mg cosθ (directed outward when the particle is above the horizontal). The centripetal requirement is T − mg cosθ = m v² / L. Energy conservation gives ½ m v² = ½ m v₀² − mg L (1 − cosθ), where v₀ is the speed at the lowest point. Combining these yields T = m v₀² / L − mg (3 cosθ − 2).

The minimum speed at the lowest point for the particle to complete the circle is determined by the condition that tension never becomes zero. The most critical point is the top of the circle (θ = π), where cosθ = −1. Setting T ≥ 0 at the top gives m vtop² / L ≥ mg, i.e. vtop ≥ √(g L). Using energy conservation between bottom and top: ½ m v₀² = ½ m vtop² + 2 mg L. Substituting the minimum vtop gives v₀ ≥ √(5 g L). If the initial speed is less than this, the string goes slack before the top and the particle follows a projectile path.

For a particle on a spherical surface (e.g., a bead on a smooth wire hoop), the normal reaction replaces tension. The condition for maintaining contact is N ≥ 0. At the top, N + mg = m vtop² / L, so the minimum speed is again √(g L). However, if the particle is constrained to a circular track (like a roller‑coaster loop), the normal force can also push outward, and the design speed is chosen to keep N within comfortable limits for passengers. The concept of “critical speed” also appears in the conical pendulum, where a mass moves in a horizontal circle while the string sweeps out a cone. The vertical component of tension balances weight: T cosφ = mg. The horizontal component provides centripetal force: T sinφ = m ω² L sinφ. Eliminating T gives ω = √(g / (L cosφ)). The period is T = 2π √(L cosφ / g), independent of the mass.

Examiners often test the distinction between a string (which can only pull) and a rod (which can push). With a light rod, the particle can have zero speed at the top and still complete the circle because the rod can exert a compressive force. The minimum speed at the bottom for a rod is then √(4 g L), derived from energy conservation with vtop = 0. Another common twist is to ask for the angle at which the string goes slack for a given initial speed; this requires solving T = 0 for θ using the tension expression above.

Superelevation Design for Railway Tracks and Aircraft Turns

Superelevation (also called cant or banking) is the practice of raising the outer rail or roadway relative to the inner one to counteract the lateral acceleration experienced by a vehicle on a curve. For railways, the design balances the centrifugal force m v² / r with the component of weight due to the tilt angle θ. The ideal superelevation angle satisfies tanθ = v² / (r g), exactly as for a frictionless banked road. However, trains operate over a wide speed range, so a single fixed cant cannot satisfy the ideal condition for all speeds. The concept of “cant deficiency” D quantifies the shortfall: D = (v² / (r g)) − tanθ. A positive cant deficiency means the train experiences a net lateral acceleration toward the outside of the curve, which must be resisted by the friction between wheel and rail. Standards limit cant deficiency to values that ensure passenger comfort and prevent wheel climb (typically D ≤ 0.1 to 0.15 in many codes). Conversely, “cant excess” occurs when a slow train on a highly banked curve feels a net inward lateral acceleration, risking derailment toward the inside; this is limited by the minimum operating speed.

Transition curves (clothoids or Euler spirals) are used to vary the superelevation gradually from zero on straight track to the full cant on the circular curve. The curvature of a clothoid increases linearly with length, providing a constant rate of change of lateral acceleration (jerk) and a smooth increase in superelevation. The length of the transition is chosen so that the rate of change of cant does not exceed a prescribed value (often 1 in 360 per metre). This ensures that the forces on the vehicle and the track structure vary smoothly, reducing wear and improving ride quality.

In aviation, banking is achieved by tilting the lift vector. An aircraft in a coordinated turn banks at an angle φ such that the horizontal component of lift provides the centripetal force: L sinφ = m v² / r. The vertical component balances weight: L cosφ = mg. Dividing gives tanφ = v² / (r g), identical to the frictionless banking formula. The load factor n = L / (mg) = 1 / cosφ increases with bank angle; at φ = 60° the load factor is 2, meaning the pilot and airframe experience twice the normal weight. Structural limits and passenger comfort restrict the maximum bank angle in commercial aviation to about 25°–30°. Fighter aircraft can sustain much higher load factors (up to 9 g) and bank angles exceeding 80°. The turn radius for a given speed and bank angle is r = v² / (g tanφ). Pilots use the “standard rate turn” (3° per second) as a reference; the required bank angle for a standard rate turn at speed v (in knots) is approximately φ ≈ 0.15 v degrees.

Both railway and aircraft design must consider the variation of speed. For railways, the timetable speed, maximum permissible speed, and minimum speed determine the chosen cant and cant deficiency. For aircraft, the turn is usually executed at a constant airspeed, but wind gradients and altitude changes can alter the true airspeed and thus the required bank angle. Modern flight management systems compute the optimal bank angle continuously, while railway signalling systems enforce speed limits that keep the actual cant deficiency within safe bounds. The underlying physics — balancing weight, normal (or lift) reaction, and centripetal requirement — is the same Newtonian force analysis used for a simple banked road.

Impulse, Momentum and Friction in Collisions

The impulse–momentum theorem states that the change in linear momentum of a body equals the integral of the net external force over the collision time: Δp = ∫ F dt = J. For a system of particles, internal forces cancel in pairs, so the total momentum changes only due to external impulses. In a collision between two bodies, the contact force is large and acts for a short duration; the impulse delivered by this force determines the post‑collision velocities. If the collision is perfectly elastic, kinetic energy is also conserved, giving a second equation. The coefficient of restitution e (0 ≤ e ≤ 1) relates the relative speed of separation to the relative speed of approach along the line of impact: e = (v₂′ − v₁′) / (v₁ − v₂). For a perfectly elastic collision e = 1; for perfectly inelastic e = 0 and the bodies stick together.

When friction acts during an oblique collision, the contact force has both normal and tangential components. The normal impulse Jn governs the change in normal momentum, while the tangential impulse Jt changes the tangential momentum. If the surfaces are rough, the maximum tangential impulse is limited by the friction law: |Jt| ≤ μ Jn. In many problems the collision is assumed to be instantaneous, so the friction impulse is either sufficient to prevent relative tangential slip (sticking) or it reaches the limiting value (slipping). The condition for sticking is that the required tangential impulse to equalise the tangential velocities does not exceed μ Jn. If it does, slip occurs and the tangential impulse is Jt = −μ Jn sign(vt), where vt is the relative tangential velocity at contact.

Consider a sphere of mass m and radius R striking a rough horizontal floor with velocity components vx (horizontal) and vy (vertical downward). The normal impulse reverses the vertical momentum: Jn = m (vy′ + vy). If the collision is elastic in the normal direction, vy′ = e vy. The friction impulse changes the horizontal momentum and also exerts a torque about the centre, altering the angular velocity ω. The equations are m (vx′ − vx) = Jt and I (ω′ − ω) = −Jt R (sign depending on convention). For a solid sphere I = 2/5 m R². If the sphere initially has no spin (ω = 0) and the horizontal speed is large, the required Jt to bring the contact point to rest (no slip) may exceed μ Jn. In that case slip persists throughout the impact and the final horizontal speed is vx′ = vx − μ (1+e) vy. If the required impulse is within the limit, the contact point sticks, giving vx′ = (5 vx − 2 R ω) / 7 and ω′ = (5 ω + 2 vx / R) / 7 for a solid sphere.

These principles extend to collisions of rigid bodies with multiple contact points, such as a billiard ball striking a cushion. The cushion exerts a normal impulse perpendicular to its surface and a friction impulse parallel to it. The coefficient of restitution for the cushion is typically less than 1, and the friction coefficient determines the spin imparted to the ball. In sports physics, the “kick” of a football or the “swerve” of a cricket ball can be modelled by combining the impulse from the foot or the air (Magnus force) with the frictional interaction with the ground. Understanding the vector nature of impulse and the role of friction is essential for solving problems where the collision is not head‑on and where rotational motion is coupled to translation.

  • Confusing the direction of pseudo forces: they always oppose the acceleration of the non‑inertial frame, not the motion of the particle.
  • Assuming static friction always acts opposite to the direction of motion; in rolling it can act either up or down an incline depending on the torque applied.
  • Forgetting that the minimum speed for a vertical circle with a string is √(5gL), while with a rigid rod it is √(4gL).
  • Treating cant deficiency as a force rather than an acceleration; it is the unbalanced lateral acceleration after superelevation is accounted for.
  • Neglecting the tangential impulse limit μJn in oblique collisions, leading to impossible sticking conditions.
  • Using the coefficient of restitution for the tangential direction; it applies only to the normal component of relative velocity.
  • Overlooking that the Coriolis force vanishes only when the particle’s velocity is parallel to the rotation axis.

Variable Mass Systems and Rocket Propulsion

When the mass of a system changes with time, Newton’s second law must be written in the form Fext = d(mv)/dt. Expanding the derivative gives Fext = m dv/dt + v dm/dt. The term v dm/dt is the thrust produced by mass ejection or accretion. For a rocket expelling exhaust at a constant relative velocity u (measured in the rocket frame) the thrust magnitude is T = u |dm/dt|. The equation of motion in the absence of external forces becomes m dv/dt = u dm/dt, which integrates to the Tsiolkovsky rocket equation Δv = u ln(m0/mf). If gravity and aerodynamic drag are present, the net external force is Fext = −mg − ½ ρ CD A v² (taking upward as positive). The differential equation m dv/dt = u dm/dt − mg − ½ ρ CD A v² must be solved numerically for realistic launch trajectories. A common textbook simplification assumes constant gravity and no drag, yielding the ideal Δv. In staged rockets the mass ratio of each stage multiplies, so the total Δv is the sum of the stage contributions. The specific impulse Isp = u/g₀ is often used in engineering; it relates the exhaust velocity to the standard gravity g₀ = 9.80665 m/s². For a multistage vehicle the payload fraction is maximised when each stage has the same structural coefficient and the same exhaust velocity. Problems in competitive examinations frequently ask for the instantaneous acceleration at a given mass, the burn time required to reach a target velocity, or the maximum height attained after burnout when the rocket coasts under gravity alone.

Friction in Belt Drives and the Capstan Equation

A flexible belt wrapped around a cylindrical drum transmits tension from the tight side T₁ to the slack side T₂. When the belt is on the verge of slipping, the tension varies exponentially with the wrap angle θ (in radians) according to the capstan equation T₁ = T₂ eμθ, where μ is the coefficient of static friction between belt and drum. The derivation considers an infinitesimal element subtending angle dθ; the normal reaction on the element is dN = T dθ and the limiting friction is μ dN = μ T dθ. Balancing tangential forces gives dT = μ T dθ, which integrates to the exponential form. For a V‑belt the effective friction coefficient is increased to μeff = μ / sin(α/2), where α is the groove angle, because the normal force is amplified by the wedge action. In a flat‑belt drive the maximum transmissible power is P = (T₁ − T₂) v, with v the belt speed. The centrifugal tension Tc = m v² (where m is mass per unit length) reduces the effective tight‑side tension to T₁ − Tc. Design problems often require finding the minimum wrap angle to avoid slip for a given power, or the required coefficient of friction when the geometry is fixed. The capstan equation also applies to rope‑on‑bollard mooring, where a few turns can hold a large ship with a modest holding force. In examinations, a typical twist is to give the belt speed and ask for the maximum power before slip, requiring the student to subtract centrifugal tension before applying the exponential relation.

Worked Example: Capstan with Centrifugal Tension
A flat belt of mass per unit length 0.15 kg/m runs at 12 m/s over a pulley with a wrap angle of 3π/2 rad. The coefficient of static friction is 0.3. The slack‑side tension is 200 N. Find the maximum power that can be transmitted without slip.
Centrifugal tension Tc = m v² = 0.15 × 12² = 21.6 N. Effective tight‑side tension limit from capstan: T₁ = T₂ eμθ = 200 × e0.3 × 3π/2 = 200 × e1.4137 ≈ 200 × 4.111 = 822.2 N. Net driving tension = (T₁ − Tc) − T₂ = (822.2 − 21.6) − 200 = 600.6 N. Power P = (net tension) × v = 600.6 × 12 = 7207 W ≈ 7.2 kW.
Exam‑Day Strategy
When a belt‑drive problem appears, first compute centrifugal tension and subtract it from the tight‑side limit given by the capstan equation. Many candidates forget the centrifugal term and overestimate the transmissible power. Write the capstan relation in logarithmic form (ln(T₁/T₂) = μθ) to solve quickly for any unknown variable.

Dynamics of a Particle on a Rotating Platform: Coriolis and Centrifugal Effects

In a reference frame rotating with constant angular velocity Ω about a fixed vertical axis, a particle of mass m moving with velocity v′ relative to the platform experiences two fictitious forces: the centrifugal force Fcf = m Ω² r directed radially outward, and the Coriolis force Fcor = 2m Ω × v′ perpendicular to both Ω and v′. The equation of motion in the rotating frame is m a′ = Freal + Fcf + Fcor. For a particle constrained to move along a radial groove on a horizontal turntable, the Coriolis force acts tangentially, causing a sideways deflection that must be supplied by the groove’s reaction. If the groove is frictionless, the particle’s radial equation is m (r̈ − r Ω²) = 0, giving r(t) = A eΩt + B e−Ωt. With initial conditions r(0)=r₀, ṙ(0)=0, the solution is r = r₀ cosh(Ωt), showing exponential outward motion driven solely by the centrifugal term. When the particle moves on a frictionless horizontal surface without a groove, the Coriolis force curves the trajectory into an inertial circle of radius R = v′/(2Ω) (for motion initially perpendicular to Ω). In meteorology, the same mathematics explains the deflection of trade winds and the formation of cyclones. Examination questions often ask for the trajectory in the rotating frame given an initial velocity, or the condition for a particle to remain at a fixed radius (which requires a real inward force equal to m Ω² r). A frequent trap is to treat the Coriolis force as a central force; it does no work because it is always perpendicular to v′, so the kinetic energy in the rotating frame changes only due to real forces and the centrifugal potential.

Energy Methods for Curved Motion: Work‑Energy Theorem in Circular and Helical Paths

The work‑energy theorem ΔK = Wnet holds for any path, but its application to constrained motion on curved surfaces simplifies when the normal reaction does no work. For a bead sliding on a frictionless circular wire of radius R in a vertical plane, the only work‑doing force is gravity. Taking the lowest point as zero potential, the speed at an angle θ from the vertical is v = √(2gR(1−cosθ) + v₀²). The normal reaction follows from the radial component of Newton’s second law: N = m(v²/R + g cosθ). If the wire is rough with coefficient μ, the friction force f = μN does negative work Wf = −∫ f ds = −μ ∫ N ds. Because N depends on v, the integral must be evaluated using the energy equation itself, leading to a differential equation for v(θ). For a helix of radius R and pitch h (vertical rise per turn), the arc length per turn is s = √((2πR)² + h²). A particle sliding under gravity on a frictionless helix has a constant tangential acceleration component g sinα, where sinα = h/s. The speed after descending a vertical distance Δy is v = √(2g Δy + v₀²), identical to free fall, because the normal force is always perpendicular to the displacement. When a constant tangential force F (e.g., a motor) acts along the helix, the work done per turn is F s, and the change in kinetic energy per turn equals F s − mg h. Problems often combine a circular loop with a helical entry ramp; the student must apply energy conservation piecewise, accounting for the work done by non‑conservative forces only on the segments where they act.

Stability of Circular Orbits under Central Forces

For a particle of mass m moving under a central force F(r) = −k rⁿ (with k>0), a circular orbit of radius r₀ exists when the centripetal requirement m v₀²/r₀ = k r₀ⁿ is satisfied. The effective potential is Ueff(r) = L²/(2mr²) + ∫ F(r) dr, where L = m r₀ v₀ is the conserved angular momentum. Stability requires d²Ueff/dr² |r₀ > 0. Computing the second derivative gives the condition n > −3. For the inverse‑square law (n = −2) the orbit is stable; for a force proportional to r (n = 1, Hooke’s law) it is also stable. The borderline case n = −3 corresponds to a force F ∝ 1/r³, where the effective potential is flat and the orbit is neutrally stable. In the Kepler problem (n = −2) the orbital period obeys T² ∝ r₀³ (Kepler’s third law). For a central force F = −k/r² + β/r³ (a relativistic correction), the effective potential acquires an extra term β/(2r²), shifting the stability condition and causing periapsis precession. Examination questions may ask to derive the stability criterion for a given power‑law force, or to find the frequency of small radial oscillations about the circular orbit, which is ωr = Ω √(3+n) where Ω = v₀/r₀ is the angular frequency of the circular motion. A common mistake is to confuse the condition for existence of a circular orbit (force balance) with the condition for its stability (second derivative of effective potential).

  • Treating the Coriolis force as a radial force; it is always perpendicular to the instantaneous velocity in the rotating frame.
  • Forgetting to subtract centrifugal tension before applying the capstan equation in belt‑drive problems.
  • Using the rocket equation Δv = u ln(m₀/m_f) when external forces (gravity, drag) are non‑negligible without adding the impulse of those forces.
  • Assuming the normal reaction on a curved wire does work; it does no work only when the constraint is frictionless and the wire is fixed.
  • Confusing the existence condition for a circular orbit (centripetal force balance) with the stability condition (second derivative of effective potential).
  • Neglecting the sign of the Coriolis term when the particle moves opposite to the rotation direction, leading to an incorrect deflection sense.
  • Applying the coefficient of restitution to the tangential component of relative velocity in oblique collisions; it applies only to the normal component.

These advanced topics extend the core syllabus and appear regularly in higher‑difficulty physics papers, so mastering their derivations and typical pitfalls is essential for top scores.

Practice Questions

← Motion in a Plane & Projectile Motion Work, Energy & Power →