GATE — Paper (Full Paper)

59 Q · 100 marks · 180 min · Answer key + explanations

59 questions100 marks180 minutes-1/3 for a 1-mark MCQ, -2/3 for a 2-mark MCQ; no negative for numerical-answer questions

Generated 2026-11-07T02:25:28.059Z · reviewed question bank · Source: GATE: 65 questions, 100 marks, 180 minutes; General Aptitude 10 questions (15 marks), core 55 questions (85 marks).

Run this paper as a timed test
59 questions · 100 marks · 180 minutes · -1/3 for a 1-mark MCQ, -2/3 for a 2-mark MCQ; no negative for numerical-answer questions
--:--:--Negative marking: -1/3 for a 1-mark MCQ, -2/3 for a 2-mark MCQ; no negative for numerical-answer questions

Answer the questions, then press “Show answer” on any question or use the key at the bottom. This page and the PDF are printable.

Download PDF

General Aptitude 9 Q · 15 marks

Q1General Aptitude
If 15 workers can build a wall in 8 days, how many workers are needed to build same wall in 6 days?
Q2General Aptitude
If x + y = 10 and xy = 21, then x² + y² is:
Q3General Aptitude
If a train running at 72 km/h crosses a pole in 10 s, the length of train is:
Q4General Aptitude
If the radius of a circle is doubled, the area becomes:
Q5General Aptitude
Simplify: 25 + 5 x 2 - 10
Q6General Aptitude
What is the value of x in the equation 2^x + 2^x = 10?
Q7General Aptitude
If 5 men can build a wall in 12 days, how many days will 10 men take?
Q8General Aptitude
The ratio of 3 km to 300 m is:
Q9General Aptitude
Choose the correct spelling:

Core Subject 50 Q · 85 marks

Q10Core Subject
In orthogonal cutting, the cutting edge is:
Q11Core Subject
Quick sand condition occurs when:
Q12Core Subject
A stack is implemented using an array. If the top pointer is at index 5, what is the current size of the stack?
Q13Core Subject
The bending moment at a simply supported beam's center with point load P at center is:
Q14Core Subject
Beam deflection is maximum at:
Q15Core Subject
The Chezy's coefficient C in Manning's formula relates to:
Q16Core Subject
The purpose of a heat sink in power amplifiers is to:
Q17Core Subject
The impedance of a capacitor of capacitance C at frequency ω is:
Q18Core Subject
The gain of a non-inverting amplifier with Rf=10 k and R1=1 k is:
Q19Core Subject
The efficiency of Carnot cycle depends on:
Q20Core Subject
The operation of enlarging a hole is called:
Q21Core Subject
The plasticity chart classifies soil based on:
Q22Core Subject
Which data structure is used for implementing recursion?
Q23Core Subject
A 4-bit R-2R DAC uses resistors of values:
Q24Core Subject
How many AND gates are needed for 8-to-1 multiplexer?
Q25Core Subject
The height of a complete binary tree with n nodes is:
Q26Core Subject
The COP of a refrigerator is 4. If it extracts 200 J from cold reservoir, work input is:
Q27Core Subject
A diode in forward bias has:
Q28Core Subject
The number of input lines for 3-to-8 decoder is:
Q29Core Subject
What is the time complexity of binary search on a sorted array of n elements?
Q30Core Subject
In a microprocessor, what is the function of the Arithmetic Logic Unit (ALU)?
Q31Core Subject
The number of bits in a nibble is:
Q32Core Subject
The bearing capacity of soil is improved by:
Q33Core Subject
A transistor has three terminals: base, collector, and:
Q34Core Subject
The pH of pure water is:
Q35Core Subject
The void ratio of a soil is defined as:
Q36Core Subject
Which traversal gives sorted order in a BST?
Q37Core Subject
Which of the following is NOT a valid Boolean algebra property?
Q38Core Subject
Kirchhoff's current law is based on:
Q39Core Subject
A steel rod of 10 mm diameter carries 31.4 kN load. Stress is:
Q40Core Subject
The Manning's roughness coefficient n for concrete is about:
Q41Core Subject
The Otto cycle efficiency increases with:
Q42Core Subject
Class A amplifier has conduction angle of:
Q43Core Subject
The factor of safety is defined as:
Q44Core Subject
Which of the following is a linear data structure?
Q45Core Subject
Which language is accepted by Pushdown Automata?
Q46Core Subject
Which flip-flop has no race condition?
Q47Core Subject
Which casting process uses a wax pattern?
Q48Core Subject
In a min-heap, the smallest element is at:
Q49Core Subject
A material that undergoes large deformation before fracture is called:
Q50Core Subject
A Zener diode is used for:
Q51Core Subject
Which process is used to make threads on a bolt?
Q52Core Subject
The total hardness of water is due to:
Q53Core Subject
TIG welding uses which electrode?
Q54Core Subject
The SI unit of thermal conductivity is:
Q55Core Subject
In a CPU, what is the main function of the cache memory?
Q56Core Subject
Which memory has the fastest access time?
Q57Core Subject
The main function of an operating system is:
Q58Core Subject
Which scheduling algorithm is non-preemptive?
Q59Core Subject
The optimum depth of a canal is when:

Answer key

QSectionAnswer
1General AptitudeC
2General AptitudeC
3General AptitudeC
4General AptitudeB
5General AptitudeC
6General AptitudeB
7General AptitudeC
8General AptitudeC
9General AptitudeC
10Core SubjectB
11Core SubjectB
12Core SubjectA
13Core SubjectB
14Core SubjectC
15Core SubjectC
16Core SubjectC
17Core SubjectB
18Core SubjectB
19Core SubjectB
20Core SubjectC
21Core SubjectB
22Core SubjectC
23Core SubjectC
24Core SubjectC
25Core SubjectC
26Core SubjectC
27Core SubjectB
28Core SubjectC
29Core SubjectB
30Core SubjectB
31Core SubjectB
32Core SubjectB
33Core SubjectC
34Core SubjectC
35Core SubjectB
36Core SubjectC
37Core SubjectD
38Core SubjectB
39Core SubjectC
40Core SubjectC
41Core SubjectB
42Core SubjectC
43Core SubjectB
44Core SubjectB
45Core SubjectB
46Core SubjectC
47Core SubjectC
48Core SubjectA
49Core SubjectB
50Core SubjectC
51Core SubjectC
52Core SubjectB
53Core SubjectB
54Core SubjectB
55Core SubjectB
56Core SubjectB
57Core SubjectC
58Core SubjectB
59Core SubjectB

Solutions & explanations

Q1. If 15 workers can build a wall in 8 days, how many workers are needed to build same wall in 6 days?
Answer: C
MD = MD -> 15x8 = Mx6 -> M = 20.
Q2. If x + y = 10 and xy = 21, then x² + y² is:
Answer: C
x²+y² = (x+y)² - 2xy = 100 - 42 = 58.
Q3. If a train running at 72 km/h crosses a pole in 10 s, the length of train is:
Answer: C
Speed = 72×(5/18) = 20 m/s. Length = 20×10 = 200 m.
Q4. If the radius of a circle is doubled, the area becomes:
Answer: B
A ∝ r². If r → 2r, A → 4A.
Q5. Simplify: 25 + 5 x 2 - 10
Answer: C
Using BODMAS: 5x2=10, 25+10-10=25.
Q6. What is the value of x in the equation 2^x + 2^x = 10?
Answer: B
Given equation is 2^x + 2^x = 10, which can be simplified as 2 * 2^x = 10, then 2^x = 5. Since 2^2 = 4 and 2^3 = 8, the value of x that satisfies the equation is between 2 and 3, but closest to the given options is 2.
Q7. If 5 men can build a wall in 12 days, how many days will 10 men take?
Answer: C
MD = MD -> 5x12 = 10xD -> D = 6 days.
Q8. The ratio of 3 km to 300 m is:
Answer: C
3 km = 3000 m. 3000:300 = 10:1.
Q9. Choose the correct spelling:
Answer: C
Correct spelling: Mischievous.
Q10. In orthogonal cutting, the cutting edge is:
Answer: B
Orthogonal cutting: cutting edge ⊥ to cutting velocity direction.
Q11. Quick sand condition occurs when:
Answer: B
Quicksand: upward hydraulic gradient critical gradient (ic = Gs-1)/(1+e).
Q12. A stack is implemented using an array. If the top pointer is at index 5, what is the current size of the stack?
Answer: A
If top = 5 (0-indexed), there are 6 elements at indices 0 through 5.
Q13. The bending moment at a simply supported beam's center with point load P at center is:
Answer: B
Mmax = PL/4 for simply supported beam with central point load.
Q14. Beam deflection is maximum at:
Answer: C
Deflection depends on loading type. For UDL: max at center. For point load: at load point.
Q15. The Chezy's coefficient C in Manning's formula relates to:
Answer: C
Manning: V = (1/n)R^(2/3)S^(1/2). Chezy: C = (1/n)R^(1/6).
Q16. The purpose of a heat sink in power amplifiers is to:
Answer: C
Heat sink dissipates excess heat from power transistors to prevent thermal damage.
Q17. The impedance of a capacitor of capacitance C at frequency ω is:
Answer: B
Zc = 1/(jωC) = -j/(ωC).
Q18. The gain of a non-inverting amplifier with Rf=10 k and R1=1 k is:
Answer: B
Gain = 1 + Rf/R1 = 1 + 10 = 11.
Q19. The efficiency of Carnot cycle depends on:
Answer: B
η = 1 - T2/T1 (depends only on source and sink temperatures).
Q20. The operation of enlarging a hole is called:
Answer: C
Boring enlarges an existing hole. Reaming gives smooth finish.
Q21. The plasticity chart classifies soil based on:
Answer: B
Casagrande's plasticity chart: LL vs PI to classify fine-grained soils (CL, CH, ML, MH).
Q22. Which data structure is used for implementing recursion?
Answer: C
Recursion uses the call stack (LIFO) to store function call frames and return addresses.
Q23. A 4-bit R-2R DAC uses resistors of values:
Answer: C
R-2R ladder DAC uses only R and 2R resistors for binary-weighted conversion.
Q24. How many AND gates are needed for 8-to-1 multiplexer?
Answer: C
8-to-1 MUX needs 8 AND gates (one per input) + 1 OR gate.
Q25. The height of a complete binary tree with n nodes is:
Answer: C
Height of a complete binary tree with n nodes is logn.
Q26. The COP of a refrigerator is 4. If it extracts 200 J from cold reservoir, work input is:
Answer: C
COP = Q/W -> 4 = 200/W -> W = 50 J.
Q27. A diode in forward bias has:
Answer: B
Forward bias: diode conducts with low resistance (~0.7 V drop for Si).
Q28. The number of input lines for 3-to-8 decoder is:
Answer: C
3-to-8 decoder: 3 inputs, 8 outputs.
Q29. What is the time complexity of binary search on a sorted array of n elements?
Answer: B
Binary search divides the search space in half each iteration, giving O(log n) time complexity.
Q30. In a microprocessor, what is the function of the Arithmetic Logic Unit (ALU)?
Answer: B
The Arithmetic Logic Unit (ALU) in a microprocessor performs arithmetic operations such as addition, subtraction, multiplication, and division, as well as logical operations such as AND, OR, and NOT.
Q31. The number of bits in a nibble is:
Answer: B
1 nibble = 4 bits. 1 byte = 2 nibbles = 8 bits.
Q32. The bearing capacity of soil is improved by:
Answer: B
Compaction increases soil density → higher bearing capacity.
Q33. A transistor has three terminals: base, collector, and:
Answer: C
BJT terminals: Base, Collector, Emitter. FET: Gate, Drain, Source.
Q34. The pH of pure water is:
Answer: C
Pure water has pH 7 at 25°C (neutral).
Q35. The void ratio of a soil is defined as:
Answer: B
Void ratio e = Vv/Vs (volume of voids / volume of solids).
Q36. Which traversal gives sorted order in a BST?
Answer: C
Inorder traversal of BST visits nodes in ascending order (left -> root -> right).
Q37. Which of the following is NOT a valid Boolean algebra property?
Answer: D
A + A = A (idempotent law), not 0. A + A = 1 and A . A = 0.
Q38. Kirchhoff's current law is based on:
Answer: B
KCL: sum of currents entering = sum leaving (charge conservation).
Q39. A steel rod of 10 mm diameter carries 31.4 kN load. Stress is:
Answer: C
A = p(0.01)²/4 = 7.85×10⁻⁵ m². s = 31400/7.85e-5 = 400 MPa.
Q40. The Manning's roughness coefficient n for concrete is about:
Answer: C
Manning's n for concrete: 0.012-0.015 (typically 0.013).
Q41. The Otto cycle efficiency increases with:
Answer: B
η = 1 - 1/r^(γ-1). Higher compression ratio → higher efficiency.
Q42. Class A amplifier has conduction angle of:
Answer: C
Class A: conducts for full 360 degrees of input cycle -> low efficiency (~25%).
Q43. The factor of safety is defined as:
Answer: B
FoS = ultimate load / allowable load = ultimate stress / working stress.
Q44. Which of the following is a linear data structure?
Answer: B
Queue is linear (elements in sequence). Tree and Graph are non-linear data structures.
Q45. Which language is accepted by Pushdown Automata?
Answer: B
PDA accepts exactly the class of Context-Free Languages (CFL).
Q46. Which flip-flop has no race condition?
Answer: C
Master-slave JK flip-flop eliminates race-around condition.
Q47. Which casting process uses a wax pattern?
Answer: C
Investment (lost wax) casting: wax pattern coated with ceramic, melted out, metal poured.
Q48. In a min-heap, the smallest element is at:
Answer: A
Min-heap property: parent ≤ children, so root is always the minimum element.
Q49. A material that undergoes large deformation before fracture is called:
Answer: B
Ductile materials (steel, aluminum) undergo significant plastic deformation before fracture.
Q50. A Zener diode is used for:
Answer: C
Zener diode maintains constant voltage in reverse breakdown -> voltage regulator.
Q51. Which process is used to make threads on a bolt?
Answer: C
Threading (using dies) cuts external threads on bolts and rods.
Q52. The total hardness of water is due to:
Answer: B
Hardness: Ca²⁺ and Mg²⁺ ions (temporary: bicarbonates, permanent: sulfates/chlorides).
Q53. TIG welding uses which electrode?
Answer: B
TIG (Tungsten Inert Gas) uses non-consumable tungsten electrode.
Q54. The SI unit of thermal conductivity is:
Answer: B
Thermal conductivity k: W/(m.K).
Q55. In a CPU, what is the main function of the cache memory?
Answer: B
The main function of the cache memory in a CPU is to store frequently used data and instructions, which reduces the time taken to access the main memory.
Q56. Which memory has the fastest access time?
Answer: B
Cache memory is closest to the CPU and has the fastest access time (nanoseconds), followed by RAM, then SSD, then HDD.
Q57. The main function of an operating system is:
Answer: C
The OS manages CPU, memory, I/O devices, and provides resource allocation and protection.
Q58. Which scheduling algorithm is non-preemptive?
Answer: B
First Come First Serve (FCFS) is non-preemptive - once a process gets the CPU, it runs until completion or I/O.
Q59. The optimum depth of a canal is when:
Answer: B
Most economical section: max hydraulic radius → min wetted perimeter.