GATE Practice Set 16

15 Q · 42 min · 23 marks · Paper pattern

Generated 2026-11-18 · Paper pattern

Time Remaining: 42:00

Click any option to check your answer.

Sections: Core SubjectGeneral Aptitude
Q1. Core Subjectmodel-generated · 2026-11-18
A simply supported beam of length 4 m carries a point load of 10 kN at mid‑span. The flexural rigidity EI is 2×10⁶ N·m². The maximum deflection (in mm) is approximately:
A. 7 mm
B. 5 mm
C. 10 mm
D. 15 mm
Correct Answer: A
Shortcut: δ = PL³/(48EI). Plug P=10 kN=10⁴ N, L=4 m → L³=64, numerator=6.4×10⁵ N·m³. Denominator=48×2×10⁶=9.6×10⁷. δ=6.4×10⁵/9.6×10⁷=0.00667 m=6.7 mm ≈ 7 mm. Full: Using the standard formula for central point load on a simply supported beam, the maximum deflection is PL³/(48EI). Substituting the given values yields 6.7 mm, closest to 7 mm.
Q2. Core Subjectmodel-generated · 2026-11-18
A ball bearing is rated for a life of 10,000 hours at a radial load of 5 kN. If the load is increased to 10 kN, the expected life (in hours) is approximately? (Assume load-life exponent k = 3 for ball bearings)
A. 2500
B. 5000
C. 1250
D. 8000
Correct Answer: C
Shortcut: Bearing life L ∝ 1/Pᵏ. Load doubles (P₂/P₁ = 2), so life reduces by factor 2³ = 8. 10,000 / 8 = 1,250 hours. Full Solution: The load-life relationship is L₁₀ = (C/P)ᵏ or L₁P₁ᵏ = L₂P₂ᵏ. Given L₁ = 10,000 hrs, P₁ = 5 kN, P₂ = 10 kN, k = 3. L₂ = L₁ × (P₁/P₂)ᵏ = 10,000 × (5/10)³ = 10,000 × (1/8) = 1,250 hours.
Q3. Core Subjectmodel-generated · 2026-11-18
A spring‑mass system has stiffness k = 1×10⁵ N/m and mass m = 10 kg. The natural frequency (in Hz) is approximately:
A. 10 Hz
B. 12 Hz
C. 14 Hz
D. 16 Hz
Correct Answer: D
Shortcut: f = (1/2π)√(k/m). √(k/m)=√(10⁵/10)=√10⁴=100 rad/s. f=100/(2π)≈100/6.283≈15.9 Hz ≈ 16 Hz. Full: Natural angular frequency ω_n=√(k/m)=100 rad/s, convert to Hz by dividing by 2π, giving ≈15.9 Hz, nearest 16 Hz.
Q4. Core Subjectmodel-generated · 2026-11-18
A steam pipe is insulated with a material of thermal conductivity 0.1 W/m·K. The outer surface convection heat transfer coefficient is 10 W/m²·K. The critical radius of insulation (in mm) is approximately:
A. 5 mm
B. 10 mm
C. 20 mm
D. 50 mm
Correct Answer: B
Shortcut: For a cylinder, critical radius r_c = k_ins / h. Here r_c = 0.1 / 10 = 0.01 m = 10 mm. Full method: Heat loss from insulated pipe increases with insulation thickness until r = k/h, then decreases. Substituting k = 0.1 W/m·K and h = 10 W/m²·K gives r_c = 0.01 m = 10 mm.
Q5. General Aptitudemodel-generated · 2026-11-18
A and B together can complete a work in 12 days. B and C together can complete it in 15 days. C and A together can complete it in 20 days. In how many days can A alone complete the work?
A. 30 days
B. 40 days
C. 50 days
D. 60 days
Correct Answer: A
Shortcut: Take LCM of 12, 15, 20 = 60 as total work. Then daily work of (A+B)=5, (B+C)=4, (C+A)=3. Sum = 12 = 2(A+B+C) => A+B+C=6. So A's daily work = 6-4=2. Time for A = 60/2 = 30 days. Full solution: Let total work = 60 units. Efficiency of A+B = 60/12 = 5 units/day, B+C = 60/15 = 4, C+A = 60/20 = 3. Adding gives 2(A+B+C)=12 => A+B+C=6. Subtract B+C (4) from total (6) gives A=2 units/day. Hence A alone takes 60/2 = 30 days.
Q6. Core Subjectmodel-generated · 2026-11-18
A Carnot refrigerator operates between −10 °C and 30 °C. Its coefficient of performance (COP) is approximately:
A. 5.5
B. 6.5
C. 7.5
D. 8.5
Correct Answer: B
Shortcut: COP = T_L/(T_H−T_L) with temperatures in Kelvin. T_L = 263 K (−10 °C), T_H = 303 K (30 °C), ΔT = 40 K → COP = 263/40 ≈ 6.58 ≈ 6.5. Full: Convert Celsius to Kelvin, apply the Carnot refrigerator COP formula, compute 263/40 = 6.575, nearest option 6.5.
Q7. Core Subjectmodel-generated · 2026-11-18
In a turning operation using a carbide tool, the tool life is 80 minutes at a cutting speed of 30 m/min. If the Taylor's tool life exponent (n) is 0.5, the cutting speed (in m/min) required to achieve a tool life of 20 minutes is approximately:
A. 42
B. 60
C. 75
D. 90
Correct Answer: B
Shortcut: Use the ratio form of Taylor's equation V₂ = V₁(T₁/T₂)ⁿ. Speed ratio = (80/20)⁰·⁵ = √4 = 2. New speed = 30 × 2 = 60 m/min. Full: Taylor's equation VTⁿ = C gives V₁T₁ⁿ = V₂T₂ⁿ. Substituting V₁=30, T₁=80, T₂=20, n=0.5: V₂ = 30 × (80/20)⁰·⁵ = 30 × √4 = 60 m/min.
Q8. General Aptitudemodel-generated · 2026-11-17
Find the missing term in the following series: 2, 6, 12, 20, 30, ?
A. 40
B. 44
C. 42
D. 46
Correct Answer: C
Shortcut: Calculate successive differences: 4, 6, 8, 10. Differences increase by 2 constantly. Next difference = 12. Missing term = 30 + 12 = 42. Full: The series follows the pattern n(n+1): 1×2=2, 2×3=6, 3×4=12, 4×5=20, 5×6=30, 6×7=42.
Q9. Core Subjectmodel-generated · 2026-11-18
A cubic casting of side 50 mm solidifies in 5 minutes. Using Chvorinov's rule (t = B(V/A)^2), the solidification time (in minutes) for a cubic casting of the same material with side 100 mm is approximately:
A. 10
B. 40
C. 80
D. 20
Correct Answer: D
Shortcut: For a cube, V/A = a/6, so solidification time t ∝ a². Doubling the side length (50 mm → 100 mm) increases time by factor 2² = 4. 5 min × 4 = 20 min. Full Solution: Chvorinov's rule states t = B(V/A)². For a cube of side 'a', Volume = a³, Surface Area = 6a², so V/A = a/6. Thus t = B(a/6)² ∝ a². For a₁ = 50 mm, t₁ = 5 min. For a₂ = 100 mm = 2a₁, t₂/t₁ = (a₂/a₁)² = 4. Therefore t₂ = 4 × 5 = 20 min.
Q10. Core Subjectmodel-generated · 2026-11-17
A simply supported beam of length 4 m carries a uniformly distributed load of 10 kN/m. The maximum bending moment (in kN·m) occurs at mid-span and equals:
A. 40
B. 60
C. 20
D. 80
Correct Answer: C
Shortcut: For UDL on simply supported beam, M_max = wL^2/8 = 10×4^2/8 = 20 kNm. Full: Reactions = wL/2 = 20 kN each; moment at centre = 20×2 – 10×2×1 = 40 – 20 = 20 kNm.
Q11. Core Subjectmodel-generated · 2026-11-18
An ideal Brayton cycle operates with a pressure ratio of 8. Assuming specific heat ratio γ = 1.4, the thermal efficiency (in %) is approximately:
A. 35
B. 55
C. 45
D. 65
Correct Answer: C
Shortcut: Brayton efficiency η = 1 - (1/rₚ)^((γ-1)/γ). Here (γ-1)/γ = 0.4/1.4 = 2/7 ≈ 0.286. rₚ^0.286 = 8^(2/7) = (2³)^(2/7) = 2^(6/7) ≈ 1.81. η ≈ 1 - 1/1.81 ≈ 0.447 ≈ 45%. Full Solution: For an ideal Brayton cycle, thermal efficiency depends only on pressure ratio rₚ and γ. η = 1 - 1/(rₚ)^((γ-1)/γ). Substituting rₚ = 8, γ = 1.4: Exponent = 0.4/1.4 = 2/7. (8)^(2/7) = 2^(6/7) ≈ 1.811. η = 1 - 1/1.811 = 0.4478 = 44.78% ≈ 45%.
Q12. Core Subjectmodel-generated · 2026-11-18
An ideal Diesel cycle operates with a compression ratio of 16 and a cut-off ratio of 2. Taking the specific heat ratio γ = 1.4, the air-standard thermal efficiency (in %) is approximately:
A. 55
B. 58
C. 61
D. 67
Correct Answer: C
Shortcut: Compute 1/r^(γ-1) ≈ 1/16^0.4 ≈ 1/3.03 ≈ 0.33. Cut-off term (ρ^γ-1)/[γ(ρ-1)] ≈ (2^1.4-1)/1.4 ≈ 1.64/1.4 ≈ 1.17. Product ≈ 0.386. Efficiency ≈ 1 - 0.386 = 61.4%. Full: η = 1 - (1/r^(γ-1)) * [(ρ^γ - 1)/(γ(ρ - 1))]. r=16, ρ=2, γ=1.4. r^(γ-1)=16^0.4≈3.031. ρ^γ=2^1.4≈2.639. Term = (1/3.031) * (1.639/1.4) = 0.33 * 1.171 = 0.386. η = 1 - 0.386 = 0.614 ≈ 61%.
Q13. Core Subjectmodel-generated · 2026-11-18
A centrifugal pump running at 1000 rpm delivers 0.1 m³/s against a head of 50 m. If the pump speed is increased to 1500 rpm, the new discharge (in m³/s) and head (in m) are respectively:
A. 0.15, 112.5
B. 0.15, 75
C. 0.225, 112.5
D. 0.225, 75
Correct Answer: A
Shortcut: Affinity laws: Q ∝ N, H ∝ N². Speed ratio = 1500/1000 = 1.5. Q₂ = 0.1 × 1.5 = 0.15 m³/s. H₂ = 50 × (1.5)² = 50 × 2.25 = 112.5 m. Full: For dynamically similar conditions, Q₁/N₁ = Q₂/N₂ → Q₂ = 0.1 × (1500/1000) = 0.15 m³/s. H₁/N₁² = H₂/N₂² → H₂ = 50 × (1500/1000)² = 50 × 2.25 = 112.5 m.
Q14. Core Subjectmodel-generated · 2026-11-17
A data table shows the number of defective items found in successive batches: Batch 1: 12, Batch 2: 15, Batch 3: 9, Batch 4: 14. Using the quick “average of extremes” shortcut for small data sets, estimate the mean number of defects per batch.
BatchDefects
112
215
39
414
A. 10
B. 12.5
C. 13
D. 14.5
Correct Answer: B
Shortcut: Average of extremes = (first + last)/2 = (12 + 14)/2 = 13. Then adjust by noting middle values are close to 13, so final mean ≈ 12.5. Full solution: Sum = 12+15+9+14 = 50. Mean = 50/4 = 12.5.
Q15. Core Subjectmodel-generated · 2026-11-16
A solid circular shaft of diameter 40 mm transmits a torque of 377 Nm. The maximum shear stress in the shaft (in MPa) is:
A. 20 MPa
B. 25 MPa
C. 30 MPa
D. 35 MPa
Correct Answer: C
Shortcut: τ_max = 16T/(πd³). With T = 377 Nm, d = 0.04 m → τ_max ≈ 30 MPa. Full: For a solid circular shaft, maximum shear stress τ_max = 16T/(πd³). Substituting the given torque and diameter yields τ_max = 30 MPa.